STS Rear Mount - The STS rear mount affixes to the rear (or inside)  stabilizer hole in the riser of your bow.  The new E.D.S. ( Extreme Dampening System)  stopper on the end of the STS should be barely touching your string once installed correctly.  When you shoot your bow, the string will contact the E.D.S.  stopper, thus stopping the normal forward travel of the string.  Instead of traveling past the string's resting point (a common cause for wrist/forearm string slap and many errors cause by movement during the shot), the string is stopped at the resting point.  This allows you to be more accurate without the worry of string slap or fouled shots due to excessive movement.  In addition, the STS system is an effective dampener.  This will allow you to remove the speed robbing string silencing accessories, thus giving you more speed.

Included with the STS system is serving material.  Though not likely needed, you can wrap this around your bowstring where it contacts the rubber stopper to ensure that there is no excessive string wear. For those of you who prefer not to serve your string, please use some extra bow string wax in the area the E.D.S. stopper will come into contact with your string.

Also, included in the new STS's is a BigJax rod dampener made by the BowJax Co. Slide this onto your STS rod to take out additional shock and vibration.

The new E.D.S. stopper is made from a softer rubber material to make it more quiet and more absorbing for noise and vibration.  It is our most effective E.D.S. stopper made to date.

The STS front mount comes in Realtree Hardwoods HD, Realtree Hardwoods HD Green, anodized silver and anodized black color options.

Please be sure to fill out and mail in your STS warranty card that comes with your STS to activate your STS warranty.

STS Double Rear and Front Mount - Some short axle to axle bow users were noticing a small thump when using the previous STS single mount model.  In order to rectify that problem, we have created the double STS archery system.  The double STS archery system mounts to the front or rear stabilizer hole on your bow, depending upon the model used, and utilizes two STS stoppers to dampen noise and vibration. 

The STS double rear or front mount affixes to the rear or front stabilizer hole in the riser of your bow depending on the model selected.  The new E.D.S. ( Extreme Dampening System)  stopper on the end of the STS should be barely touching your string once installed correctly.  When you shoot your bow, the string will contact the E.D.S.  stopper, thus stopping the normal forward travel of the string.  Instead of traveling past the string's resting point (a common cause for wrist/forearm string slap and many errors cause by movement during the shot), the string is stopped at the resting point.  This allows you to be more accurate without the worry of string slap or fouled shots due to excessive movement.  In addition, the STS system is an effective dampener.  This will allow you to remove the speed robbing string silencing accessories, thus giving you more speed.

Included with the STS system is serving material.  Though not likely needed, you can wrap this around your bowstring where it contacts the rubber stopper to ensure that there is no excessive string wear. For those of you who prefer not to serve your string, please use some extra bow string wax in the area the E.D.S. stopper will come into contact with your string.

Also, included in the new STS's is a BigJax rod dampener made by the BowJax Co. Slide this onto your STS rod to take out additional shock and vibration.

The new E.D.S. stopper is made from a softer rubber material to make it more quiet and more absorbing for noise and vibration.  It is our most effective E.D.S. stopper made to date.

The STS front mount comes in Realtree Hardwoods HD, Realtree Hardwoods HD Green, anodized silver and anodized black color options.

Please be sure to fill out and mail in your STS warranty card that comes with your STS to activate your STS warranty.

The new stopper for STS systems from Bowjax represents an improvement over previous designs.  Made of a two part system, the four dots ensure that the string is aligned directly in the middle of the stopper.  Bottom line, this will improve your string suppression device.